› Tenant ID: fails on headless Linux (containers, VMs, CI) because
no D-Bus Secret Service is available and the keychain resolver refuses
to construct. Add an explicit --insecure-file-store flag that enables
dry's plaintext file fallback (~/.config/safedep/creds.json, mode 0600)
for writing.
Reading is fallback-enabled unconditionally in the credential resolver
chain, logout and setup info, so stored file credentials resolve with
no extra flags and logout can always clear them. On systems with a
working keychain the file provider is never constructed.
`pmg setup doctor` reported npm protection as OK on a machine with no npm
installed. Two compounding defects:
1. The availability gate used a plain `exec.LookPath`, which resolves the PMG
shim on PATH rather than the real binary, so the "skip" branch never fired.
It now uses `shim.ResolveRealBinary` (PATH with shim dirs stripped), matching
the runner, so a missing real binary correctly yields WARN "not available".
2. The result was inferred purely from a non-zero exit, so PackageManagerNotFound
(exit 127) and other failures were misread as a successful block. The check
now requires PMG's block headline in the captured output before reporting
PASS; other non-zero exits report WARN with the error surfaced.
The block headline is extracted into `ui.MalwareBlockedHeadline` so the doctor's
marker stays in sync with what PMG prints across its block-output sites.
* feat: add Linux system-wide setup
Install shared shims, managed configuration, and login-shell PATH integration so golden images and multi-user hosts can protect package installs for every user.
Co-authored-by: Cursor <cursoragent@cursor.com>
* chore: keep local design documents untracked
Co-authored-by: Cursor <cursoragent@cursor.com>
* fix: harden and simplify Linux system install
Tighten shim detection, profile repair, and install ordering while
trimming over-specific doctor/info hints from the system-install path.
Co-authored-by: Cursor <cursoragent@cursor.com>
* fix: clarify system-install doctor alias and shim path checks
Use UserBinDir for PATH checks and pass aliases as not required under
system install without treating that as active interception.
Co-authored-by: Cursor <cursoragent@cursor.com>
* fix: tighten event-log soft-fail warning prefix
Prefix the warning with [pmg] and drop the redundant continuing clause.
Co-authored-by: Cursor <cursoragent@cursor.com>
* ci: add Linux system-install e2e and pin pnpm for add flake
Cover root system setup, PATH/profile.d, managed config, non-root
interception, and remove. Pin pnpm 11.10.0 on the package-manager e2e
job after an integrity crash on pnpm add.
Co-authored-by: Cursor <cursoragent@cursor.com>
* chore: bump packageManager to pnpm 11.10.0 for e2e
Align package.json with the pnpm version we want in CI so action-setup
stops erroring on a version mismatch after the e2e integrity flake.
Co-authored-by: Cursor <cursoragent@cursor.com>
* ci: use npm init for pnpm e2e to avoid integrity crash
pnpm 11.x `pnpm init` still writes onFail:download; `pnpm add` then
fails after PMG analysis even on 11.10.0. Seed the temp package with
npm init instead.
Co-authored-by: Cursor <cursoragent@cursor.com>
* chore: revert packageManager pin to pnpm 11.1.3
The e2e integrity crash is avoided by npm init; the 11.10.0 bump is
no longer needed.
Co-authored-by: Cursor <cursoragent@cursor.com>
* fix: harden system-install review findings
Require root-owned, non-group/other-writable pmg for --system install;
allow remove without that validation. Doctor checks npm resolution for
PATH precedence, uses ImpliesInterception instead of message matching,
and documents version-manager shadowing. Pass profile bin dir from the
shim manager and note that system config ignores per-user files.
Co-authored-by: Cursor <cursoragent@cursor.com>
* fix: harden doctor PATH checks and attribute cloud events by OS user
Doctor now verifies every installed package manager against the shim
directory, and system-install validation only requires a safe parent
directory. Cloud sync records username/uid on invocation context for
multi-user hosts sharing one endpoint.
Co-authored-by: Cursor <cursoragent@cursor.com>
* fix: address system-install review findings
- shim: make system executable resolution injectable so tests pass under
umask 002; skip the root-owner test when running as root
- doctor: treat resolution into either the system or per-user shim dir as
intercepted, and collapse the shim-in-PATH check to a single call site
- setup: make remove (both --system and per-user) best-effort with
errors.Join so one failed step no longer strands the other artifact
- shim: allow a group-writable install parent dir (Debian/Ubuntu ship
/usr/local/bin as root:staff 2775) while still rejecting world-writable
and non-root-owned parents
- audit: attribute cloud events to SUDO_USER when running under sudo
- docs: drop the soft-fail event-logging claim (hard-fail is retained)
* ci: normalize /usr/local/bin perms before system-install e2e
The GitHub ubuntu-latest runner ships /usr/local/bin world-writable so
tooling can install without sudo. System install correctly refuses a
world-writable dir for the shared binary (any local user could replace
it and hijack every user's npm/pip). No FHS-compliant distro or Docker
image ships it world-writable — it is always root:root 0755 or
root:staff 2775 — so this normalizes only the anomalous CI runner back
to standard perms and still exercises the real /usr/local/bin path.
* fix: actionable remedy for root-created per-user config dir
A pmg run as root with a preserved HOME (GitHub runners, sudo -E, su
without -) creates the invoking user's ~/.config/safedep as root-owned,
and event-log init then fail-closes every later non-root command.
Make that state self-solvable:
- event-log init permission errors exit with a usefulerror naming the
likely cause and the chown fix instead of a bare fatal
- pmg setup doctor probes event-log dir writability and reports the
same fix via a new per-result Fix override
- document the mechanism and remedy in system-install.md, along with
the binary ownership requirements for --system
- consolidate this branch's doctor tests into doctor_test.go
* fix: resolve per-user paths from root's own home when running as root
Path resolution trusted HOME (and XDG_*), which sudo and su can preserve
from the invoking user (GitHub runners, sudo -E, su without -). Any pmg
run as root then created root-owned ~/.config/safedep inside that user's
home, and event-log init fail-closed every later non-root pmg/npm/pip
run for them. System install made sudo pmg the documented flow, turning
this latent bug into the happy path.
When euid is 0, configDir and cacheDir now resolve from root's passwd
home instead of the environment, so root state lands under /root and
user homes are never touched. PMG_CONFIG_DIR/PMG_CACHE_DIR still win,
non-root resolution is unchanged, and Windows is unaffected (no euid).
Event-log init stays fatal on failure; sudo-run package events are
attributed via SUDO_USER and synced by the exit auto-sync as usual.
E2E: GitHub runners preserve HOME under sudo, so assert that no sudo
pmg run leaks state into the runner's home, and that the managed-config
refusal fails for the documented reason rather than a permission brick.
* fix: triage the unwritable config dir remedy by cause
The chown hint is only correct when another account created files
inside the current user's own home. When a leaked HOME or
XDG_CONFIG_HOME points at another user's home (e.g. sudo -u on GitHub
runners), following it would chown that user's directory and brick
their pmg instead. Classify the failure against the passwd home,
which the leaked environment cannot influence, and prescribe:
- dir inside own home: restore ownership with chown
- dir outside own home: fix the leaked environment, never chown
- explicit PMG_CONFIG_DIR: make it writable
Used by both the fatal event-log error and the doctor check, and the
docs troubleshooting now carries the same two-case triage.
* ci: pin XDG_CONFIG_HOME for the cross-user e2e step; terse doctor fix
GitHub runners export XDG_CONFIG_HOME=/home/runner/.config and it leaks
through sudo -u, so the pmgtest pmg resolved the runner user's config
dir and fail-closed on its runner-owned log file (run 29289868727 shows
the triaged error catching exactly this). Set it inside the login shell
so it wins regardless of how the leak is delivered.
The remedy now returns a full-help and doctor-table pair from a single
triage, and drops the do-not-chown tail from the leak message.
* fix: adapt event-log error to the two-value remedy signature
Belongs with the previous commit; it was left unstaged and e0580b1
does not compile without it.
* fix: fall back to env path resolution when root has no passwd entry
Running as uid 0 without a resolvable root passwd entry (scratch
containers, minimal chroots) panicked at startup on every command,
because the euid-based path resolution had no fallback. Fall back to
env-derived resolution there: without a passwd database there is no
user switching, so the cross-user poisoning that branch prevents
cannot occur.
Also restore the underlying cause in the generic event-log init error
(minimal output hid it after the usefulerror change), and document
that root's per-user data lives under /root regardless of a preserved
HOME.
* fix: gate SUDO_USER trust and root path diversion; add doctor binary check
Address review findings on the system-install PR:
- cloud_sink: honor SUDO_USER for audit attribution only when euid==0.
Without the gate any user could set SUDO_USER and spoof cloud-audit
attribution to another account. Matches the guard in cmd/setup/cert.go.
- config: divert per-user paths to root's passwd home only on an actual
sudo elevation (euid==0 && SUDO_USER set), not for every root euid.
The blanket root diversion ignored HOME/XDG_CONFIG_HOME and silently
stopped reading genuine root users' config (golden Docker images),
regressing two tests that only fail when the suite runs as root.
Genuine root honors the environment as before; su without - leaves no
marker and stays a documented, loud-failing residual.
- doctor: add a system-only check re-validating that the binary the
installed shims exec is still root-owned and non-writable, catching
permission/ownership drift after install.
- shim: fold the duplicated shim-scan loop into firstShimContent.
* fix: harden system dirs at install; keep sudo attribution without passwd
Address remaining review comments:
- shim: force root:root 0755 on the managed system dirs (shim tree and
profile.d) after MkdirAll. A pre-created dir with weaker ownership,
possible under Debian's group-writable /usr/local/lib, would let a
non-root user replace the shims every account executes.
- audit: when SUDO_USER has no passwd entry (minimal containers),
attribute cloud events from sudo's recorded SUDO_USER/SUDO_UID env
instead of falling back to root. Still gated on euid 0.
- setup: reword the root-without---system warning; alias/shim install
follows HOME, so claiming it configures only root's home was wrong.
- shim: skip the non-root-owner validation test on Windows, where file
ownership is not resolvable.
* fix: reject system binaries unreachable by other users; consistent info
The system-install validation checked the binary's own permissions and
the parent's tamper-safety but never reachability: a 0755 root-owned
binary under a 0700 directory (e.g. /root/pmg) passed every check while
every non-root user's shim failed with exit 127. Walk the directory
chain to / and require the search bit for others; doctor's system
binary check inherits this. E2E gains a reject case for a binary under
a non-searchable directory.
setup info: render alias/user-shim/system-shim rows through one
installed-state formatter (location when installed, "not installed"
otherwise) instead of a mix of booleans, paths, and prose.
* fix: stop reowning /etc/profile.d; document group-writable and su gaps
writeSystemProfile chowned/chmod'd /etc/profile.d itself, a shared
system directory pmg does not own, silently overriding any perms a
sysadmin set on it. Secure only the file pmg writes (pmg.sh) via
secureSystemFile, which also forces 0644 explicitly so a restrictive
root umask cannot leave the snippet non-world-readable (which would
drop the shim dir from other users' login-shell PATH).
Docs: add Limitations entries for the group-writable install dir
bypass (validation is defeatable on non-sticky group-writable dirs
like Debian's /usr/local/bin) and the elevation-only scope (su without
- can still poison the caller's home; sudo -u cannot poison another
account). Trim the requireSafeParentDir comment to a pointer.
* refactor: separate unwritable-dir diagnosis from remedy rendering
Address the open review threads on #376:
- rename realUserHomeDir to currentUserHomeDir and fail when the passwd
entry has no home directory
- split UnwritableConfigDirRemedy into classifyUnwritableDir (cause
diagnosis) and pure message rendering so each function has one job
- replace cmd/setup's duplicate pathIsUnderDir with the shared
config.PathWithinDir, now guarding empty inputs
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_011rWmR6NS47FpedJsrTWk8A
* fix: repair umask-clamped modes on system shims and managed config
os.WriteFile and os.MkdirAll honor the process umask, so a hardened root
umask (e.g. 077) produced 0700 shims other users cannot execute and a
0600/0700 managed config non-root pmg runs cannot read - silently
disabling the system-wide policy. Chmod/chown the artifacts explicitly
after writing, with unix regression tests running under umask 077.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_011rWmR6NS47FpedJsrTWk8A
* refactor: address system-install maintainability review
- move PathWithinDir and the root-owned mkdir/chmod helpers into a new
internal/fsutil package; config no longer exports a generic fs util
- create managed-config directories with MkdirAllRootOwned, which only
sets ownership and mode on directories it creates - drops the
hardcoded safedep parent-dir heuristic and never touches pre-existing
directories
- collapse NewSystemShimManagerForRemove into NewSystemShimManager and
validate the executable in Install, where the action needs it; Remove
works regardless of binary state
- rename ShimConfig.ManageProfile to SystemProfile and document it
- name the Linux-only system paths linuxSystemBinDir/ProfilePath and
document the Unix-only validation semantics
- share the PMG_BIN shim variable name between writeShimScript and
parseShimPMGBin via the shimPMGBinVar constant
- cloud attribution falls back to the effective uid when SUDO_UID is
absent, so sudo-invoked commands are not misattributed to root
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_011rWmR6NS47FpedJsrTWk8A
---------
Co-authored-by: Sahilb315 <bansalsahil315@gmail.com>
Co-authored-by: Cursor <cursoragent@cursor.com>
Co-authored-by: Claude <noreply@anthropic.com>
* feat(sandbox): ExecutionContext plumbing and fail-closed lockdown contract
Network lockdown needs the PMG proxy's address, which is only known at
spawn time. Thread an ExecutionContext from the proxy flow through the
runner and executor into every sandbox driver, and enforce the
network_via_proxy_only fail-closed contract: lockdown without a running
loopback proxy, or on a driver that cannot enforce it, is a hard error —
never a silent fallback to unrestricted network.
- sandbox.ExecutionContext{ProxyAddr} + 4-arg Sandbox.Execute
- sandbox.ValidateLockdown validates the proxy address (loopback only)
with usefulerror code SandboxRequiresProxy
- Seatbelt validates lockdown before translation (translation itself
lands next); bubblewrap and landlock reject lockdown as unsupported
until Linux enforcement is implemented
- executor.WithExecutionContext, runner.ExecuteOptions.SandboxProxyAddr,
proxy flow passes the live proxy address
- ApplySandbox also validates centrally before invoking the driver
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PqMU5GNBbQvQct9nxek1VS
* fix(sandbox): require numeric in-range proxy port in ValidateLockdown
The validated port string is embedded into generated sandbox profiles,
so service names, zero, and out-of-range ports are refused.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PqMU5GNBbQvQct9nxek1VS
* fix(sandbox): fail closed on Seatbelt lockdown until translation lands
A lockdown policy that passed proxy validation would silently receive
the pre-lockdown network rules from the translator. Reject it until the
lockdown profile translation is implemented, keeping the window between
plumbing and enforcement fail-closed.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PqMU5GNBbQvQct9nxek1VS
* chore: review feedback — drop redundant comment, simplify stub help text
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PqMU5GNBbQvQct9nxek1VS
---------
Co-authored-by: Claude <noreply@anthropic.com>
* docs(specs): add custom block messages and package blocklist spec
* docs(specs): add custom block messages and package blocklist implementation plan
* feat(config): add blocked_packages list and custom block messages
* feat(audit): add package_blocklist_blocked event and blocklist model
* feat(proxy): block blocklisted packages in the policy gate before analysis
* feat(guard): block blocklisted packages before trust skip and analysis
* feat(ui): render blocklist blocks and custom messages, fix silent-mode block output
* feat(proxy): append custom messages to malware and go-cooldown block bodies
* test(proxye2e): cover blocklist enforcement and custom block messages
* docs(specs): remove spec and plan documents
* refactor: drop guard-flow blocklist enforcement and trim docs
Guard mode is being deprecated; the blocklist is enforced in proxy mode
only. Remove the trusted_packages mirroring references outside the docs.
* refactor(config): consolidate blocklist and block message under top-level block section
Replace dependency_cooldown.message, malware.message and blocked_packages
with a single block section: block.message is appended to every block
output regardless of which control blocked, and block.packages is the
package blocklist.
* fix(ui): render block.message as info note with clean spacing
* fix(ui): indent wrapped continuation lines in block reasons and messages
* update config template
* refactor(config): replace block section with top-level advisory_message
Remove the package blocklist (will be implemented as part of policies in
the future) and replace block.message with an optional top-level
advisory_message appended to every block output.
* chore(config): move advisory_message near top-level scalar configs in template
* fix: fail fast with clear error when package manager is not installed
When PMG shims intercept a package manager that isn't installed (e.g. a
clean JAMF-provisioned laptop where PMG is set up before dev tooling),
real-binary resolution failed with a generic "unknown" error and a
bug-report link, making it look like PMG itself had crashed.
Introduce a typed BinaryNotFoundError that exits with code 127 (standard
"command not found") and maps to a new PackageManagerNotFound error code
with an actionable message instead of the Unknown classification.
Co-authored-by: Cursor <cursoragent@cursor.com>
* fix: improve missing package manager help message
Use a concise, dynamic install hint instead of explaining PMG's
PATH forwarding internals.
Co-authored-by: Cursor <cursoragent@cursor.com>
* fix: mention PATH in missing package manager help text
Covers the common case where a package manager is installed but its bin
directory is not on PATH yet (e.g. after curl | bash install).
Co-authored-by: Cursor <cursoragent@cursor.com>
---------
Co-authored-by: Cursor <cursoragent@cursor.com>
* feat: add experimental Go module support via pmg go
Adds Go modules as a proxy-guarded ecosystem, opt-in only: the command
runs solely when invoked explicitly as `pmg go ...` and is deliberately
excluded from setup aliases and PATH shims so existing users are
unaffected.
- packagemanager: goPackageManager with fail-safe command classification
(vet/fix excluded from non-download since they can fetch on a cold
cache) and pinned-version extraction where only canonical semver
counts as explicit.
- GOPROXY normalization (fail-closed): effective GOPROXY read via
`go env` (honors go env -w), rebuilt comma-joined with `direct`
dropped so a 403 block is terminal and nothing silently falls back to
unanalyzed VCS fetches. GOPRIVATE/GONOPROXY surface a warning;
GOINSECURE is cleared. Contributed to the proxy flow through a new
ProxyRoutingProvider hook (extra child env + dynamic MITM hosts).
- Go interceptor with dynamic host matching from the user's effective
GOPROXY via InterceptorContext.GoProxyHosts. Malware analysis runs on
.zip only (the sole endpoint that delivers code); .info/.mod/@latest/
list pass through; /sumdb/ traffic and sum.golang.org are never
touched so checksum-db verification stays intact; golang.org/toolchain
is allowed on Go's own checksum verification.
- Dependency cooldown: publish time captured from .info responses
(body unmodified), in-window .zip blocked with 403; fails open for
cooldown only when the publish time was never observed.
- Cert gate: on macOS/Windows `pmg go` fails fast with actionable
guidance unless the persisted PMG CA is OS-trusted (Go ignores
SSL_CERT_FILE there); Linux works via the injected bundle.
- proxye2e: GOPROXY-protocol mock registry, Go driver and 10 hermetic
cases (allow/block/confirm, case-escaped paths, cooldown block and
fail-open, toolchain, sumdb passthrough).
Verified end-to-end on Linux: `pmg go get github.com/google/uuid@v1.6.0`
MITMs proxy.golang.org, analyzes the decoded module at the .zip fetch,
and go.sum verification succeeds through the tunneled checksum db.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_014xuhBeTVpfU4SdqVaarvuK
* fix(go): address review findings on experimental Go support
- Drop fmt/clean from NonDownloadCommands: both load packages via go
list and can download modules on a cold cache, which would bypass the
proxy under install_only.
- Support GOPROXY entries with a base path (e.g. corp Athens/JFrog at
https://corp/goproxy): the interceptor now receives host -> base URL
and strips the path prefix before parsing module URLs, so verdicts
and cooldown key on the real module path.
- Default unschemed GOPROXY entries to https, matching go's own
behavior, so corp mirrors configured as bare hosts are intercepted
instead of silently unanalyzed.
- Memoize the final verdict per module zip: go re-requests a failed
zip during go get's load phase, which double-recorded stats (the
report showed the same blocked module twice) and would have
re-prompted on Confirm verdicts.
- Fetch .info out-of-band on a cooldown cache miss: go serves .info
from its local module cache on any machine that used go before PMG,
which silently disabled cooldown. Failure of the side-fetch still
fails open for cooldown only.
- Move the noop package resolver into packagemanager.
Verified live: cold-cache cooldown block now records once; warm-cache
rerun is blocked via the side-fetch instead of failing open.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_014xuhBeTVpfU4SdqVaarvuK
* docs: collapse Go proxy-mode details by default
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_014xuhBeTVpfU4SdqVaarvuK
---------
Co-authored-by: Claude <noreply@anthropic.com>
* feat(uvx): add uvx (uv tool run) package executor
Adds support for `uvx`, implemented as a PyPI Executor alongside pipx.
uvx is an alias for `uv tool run`: it installs a tool into an ephemeral
environment and runs it, so it has no install/list subcommand and the
first positional argument (or --from) is the package to audit.
Parsing highlights:
- --from overrides the positional command as the package to audit
- --with packages are audited as additional environment dependencies
- name@version shorthand (ruff@0.3.0, ruff@latest) is normalized
- flag parsing stops at the tool name so the tool's own flags are not
misread as uvx options; uvx's value/boolean flags are registered so
none greedily consume the package positional
- VCS/URL/local-path specs are skipped for registry auditing
Wires up command registration, analytics, shell alias/shim, cloud audit
mapping, a dedicated `uvx` sandbox profile (UV_*/PIP_* env, uv cache and
tool dirs), config policy, docs, unit tests and an E2E workflow step.
Closes#326https://claude.ai/code/session_011hyLxq7oWJX5Dp4tCEfG19
* chore(uvx): align docs and base profile with uvx support
Incorporates the low-risk, non-parser improvements from the community
PR #345 (author non-responsive) into our implementation:
- list uvx (and the previously-missing pipx) as PyPI managers in the
pypi-restrictive base profile package_managers and its README, so the
base profile applies directly when selected via --sandbox-profile
- document uvx in docs/github-action.md and docs/proxy-mode.md
- add version / IsExplicitVersion assertions to the uvx parser tests
Our pflag-based parser is kept as-is: unlike #345 it audits --with
packages and handles all uvx short flags (e.g. -w), both of which the
community PR misses.
* fix(uvx): skip interpreter requests; use require in tests
Addresses review feedback on PR #357:
- uvx interpreter requests (`uvx python`, `uvx python@3.12`, `uvx pypy`,
...) launch an isolated interpreter rather than installing a PyPI tool.
Treating the positional as a package made the guard flow resolve/analyze
pkg:pypi/python (and python==3.12), which could wrongly block or fail a
valid invocation. Skip these for the positional; --with packages on the
same command are still audited.
- Use require.NoError / require.Len for fatal assertions in the uvx tests,
matching the repo's testing convention, so a failure stops the subtest
before a nil dereference instead of panicking.
* docs(uvx): document fail-open and --with-requirements trade-offs
Record the two deliberate parsing decisions raised in review as in-code
trade-off comments (no behavior change):
- unknown flags are tolerated (fail open), consistent with the other
executors; the residual gap only affects non-proxy guard mode since the
default proxy flow intercepts every registry download.
- --with-requirements / --with-editable values are consumed but not
expanded into audit targets; expanding them needs manifest-extractor and
guard changes, tracked as follow-up. Proxy mode still covers them.
* docs(uvx): drop --with-requirements limitation note
Per maintainer review: guard mode is being deprecated and auditing the
contents of an existing requirements file is a scanner's responsibility,
not PMG's. Remove the "known limitation / follow-up" note; the flags stay
registered only so their values are not mistaken for the tool positional.
---------
Co-authored-by: Claude <noreply@anthropic.com>
* feat(proxy): emit session summary on persistent proxy shutdown
The persistent proxy daemon never ran the per-invocation flow that calls
LogSessionComplete, so no session summary reached the cloud for server-mode
runs. Emit one from the daemon's aggregate stats collector on shutdown,
before the final cloud flush, so it is delivered with the run's events and
carries the CI/invocation context.
Extract the event emission into a shared LogSessionSummary(SessionData); both
the per-invocation flow and the daemon now use it. The daemon serves every
package manager, so the summary carries no single package manager.
* chore(action): shorten default cloud endpoint id prefix to gha/
* refactor(flows): extract SetupCACertificate for reuse
Move the CA load/generate/merge logic out of proxyFlow into an exported
flows.SetupCACertificate so the persistent proxy server can reuse it.
* feat(proxy): add persistent proxy server with start/stop/env/status
Introduces 'pmg proxy' commands backed by internal/proxyserver: a long-lived
MITM proxy that intercepts package managers via env vars (no shims). Supports
--daemon (Unix), --state, --port; generic 'env' output that skips cert vars
when the CA is OS-trusted; opt-in 'stop --fail-on-violation' (fail-closed on
crash) with a synchronous cloud event flush; and the malysis analysis cache.
* feat(action): add server-mode for persistent proxy
When server-mode=true the action starts the proxy daemon and injects proxy
env vars into the job instead of installing shims.
* test(proxy): add persistent proxy server E2E workflow
* docs(readme): document persistent proxy server mode
* fix(proxy): create cache dir before writing state file and daemon log
On a fresh CI runner the cache directory does not exist yet; os.OpenFile and
os.WriteFile do not create parent dirs, so 'pmg proxy start --daemon' failed
with 'no such file or directory'. MkdirAll the parent before writing.
* docs: add persistent proxy server architecture doc
* refactor proxyserver
* fix(proxy): always emit cert env vars instead of skipping on OS-trust status
npm/pip/yarn/requests trust the MITM CA inconsistently across tools, versions,
and configs; many still use bundled CA stores. Always emitting the cert-path
env vars is the conservative choice that works regardless, and is harmless for
tools that read the OS store (they ignore the vars). Skipping them when a
system CA exists would silently break any tool still on a bundled store.
* refactor(proxy): drop redundant audit init in daemon; rely on main.go
main.go's PersistentPreRun already initializes the audit pipeline for every
command (including the daemon's re-exec'd child) and closes it at process exit.
Re-initializing in proxyserver.Run created a second auditor and a second
cloud-sync WAL connection, orphaning the first. Removing it makes the daemon
consistent with the normal proxy flow, which never self-initializes audit.
* fix(proxy): bypass proxy env when flushing events to cloud on stop
pmg proxy stop inherits HTTP(S)_PROXY (injected by 'pmg proxy env') pointing at
the PMG proxy it just shut down. The cloud sync gRPC client honored those vars
and routed api.safedep.io through the dead proxy, failing with 'connection
refused' so no events were delivered. Clear the proxy env vars before the sync
so PMG's own cloud traffic goes direct.
* chore(proxy): address review feedback
- configurable bind host via proxy.server.listen_host (default loopback)
- proxy commands use ui.ErrorExit instead of returning errors to cobra
- rename errcode to ProxyPolicyViolation (covers malware + cooldown)
- share cloud sync via audit.DrainToCloud (de-dup with cmd/cloud/sync)
- centralize proxy CA bundle path in certmanager
- docs: persistent proxy cert trust + bind address
* fix(proxy): show real message on fail-on-violation error
stopExitError set only WithMsg, but ui.ErrorExit renders HumanError, so the
framed error showed 'no human-readable message available'. Set both from one
string, and emit the framed error before the stdout summary so the blocked
count is stated once.
* fix(proxy): flush cloud events from the daemon, not stop
The stop process inherits HTTP_PROXY (from 'pmg proxy env'), so its cloud
client routed api.safedep.io through the already-stopped proxy and failed with
connection refused. Move the flush into the daemon's shutdown, which has no
proxy env (it started before env injection) and dials SafeDep directly.
- daemon flushes on shutdown via audit.DrainToCloud and records the result in
the state file; stop surfaces it (on both success and fail-on-violation
paths) since the daemon's own logs aren't visible to stop
- coordinate stop's wait with the daemon shutdown budget; on timeout, error
out without reading stale state or deleting the file (fail-closed)
- persist blocked count before the flush so the gate stays correct if the
flush hangs or the daemon is killed mid-flush
- remove now-redundant cloud_flush.go
* disable auto-sync for proxy cmds
* feat(proxy): periodic cloud sync + move proxy env vars to packagemanager
- daemon runs a periodic cloud-sync ticker so the shutdown flush stays small;
the run total is reported by stop, and shutdown timeouts are coordinated
- move EnvVarForProxy from config to packagemanager (it is package-manager
knowledge); the shared function now builds the proxy URL and NO_PROXY itself,
removing the duplicated construction in the per-command and persistent paths
- relocate the #319 yarn and #339 IPv6 regression tests alongside the function
- enable cloud sync in the persistent-proxy E2E workflow and fix the stale
internal/proxystate path filter
* refactor(proxy): rename cloudFlushLockTimeout to cloudFlushLockWait
Consistent timeout naming: *LockWait is the lock-acquire bound, *Timeout is
the sync-RPC bound. Previously the final-flush pair was cloudFlushLockTimeout
vs cloudFlushTimeout — two lookalike names for different operations.
* refactor(proxy): extract cloudFlush and trim duplicate shutdown comments
The shutdown's final-flush block is now a cloudFlush helper, symmetric with
startCloudSyncLoop (one-shot vs loop). Removed the triplicated ticker/lock
contention comments, keeping the contract on the function doc and one-line
pointers at the call sites.
* docs: update persistent proxy cloud sync to daemon-owned model
The daemon now owns cloud delivery (periodic sync while serving + final flush
on shutdown); stop signals it, waits, and reports the result. Rewrite the Cloud
event sync section, fix stop attributions, add the cloud_sync state field, and
update the sequence diagram.
* docs: move Usage section up below How it works
Put the copy-paste recipes near the top so users find them before the internals.
* refactor(proxy): address PR review feedback
- configurable bind host/port via --host/--port flags + config (listen_host,
listen_port), bound directly to config fields per PMG's flag pattern
- daemon log path via --log-file and readiness timeout in ProxyDaemonConfig;
Daemonize no longer owns path policy (caller validates, fails fast)
- gate periodic cloud sync on auto_sync; suppress detached background sync for
proxy commands instead of flipping the flag
- pmg proxy env --export emits shell-quoted lines for eval (spaces survive)
- extract shared flows.BuildCachedMalysisAnalyzer, dropping the analyzer+cache
duplication between proxy flow and proxy server
- add internal/proxyserver/doc.go documenting the package + boundary vs flows
- E2E: assert malicious installs are blocked (drop continue-on-error)
- docs: trim Commands/State-file to user contracts; refresh bind address
* refactor(proxy): proactive alignment fixes from whole-PR review
- gate the shutdown cloud flush on auto_sync too, matching the periodic ticker
(auto_sync consistently controls all daemon-driven cloud delivery)
- ResolveStatePath takes cacheDir instead of *RuntimeConfig, keeping state.go
free of config dependency
- drop the empty-host comment in listenAddr; keep the loopback guard so a blank
host never silently binds all interfaces
* fix: Decouple localdb with malysis analyser construction
* fix: Persist global args before proxy server daemon exec
* fix: GitHub Action for cloud auto-sync in server mode
---------
Co-authored-by: Abhisek Datta <abhisek.datta@gmail.com>
* feat(cooldown): respect trusted_packages in dependency cooldown
Trusted packages are now treated as a superset waiver that bypasses every
PMG control (malware analysis, cooldown, and any future controls). A
globally trusted package is automatically exempt from the cooldown window
and no longer needs a duplicate entry in dependency_cooldown.skip.
The skip list remains the narrower, cooldown-only waiver for packages
that must bypass the cooldown wait but still be malware-scanned.
* refactor(cooldown): tag skip reason and audit-log skipped packages
Address review feedback on #342:
- Restore cooldownSkip to a pure single-list function (SRP); the merge
into trusted_packages now happens in a separate mergeCooldownSkip step,
driven by the exported CooldownSkip wrapper.
- Extend CooldownSkipInfo with a CooldownSkipReason (TrustedPackage /
CooldownSkipList) on both SkipAll and per-version entries, so callers
can tell apart the broad waiver from the cooldown-only one. When both
lists match the same package, trusted_packages wins.
- Add audit.LogCooldownSkipped and emit it from the npm and PyPI
interceptors on the SkipAll path, alongside the existing info log,
carrying the source list as the reason.
* refactor(cooldown): inline list merge, audit per-version exemptions
Address further review feedback:
- Drop the separate mergeCooldownSkip helper; cooldownSkip now writes
into a shared *CooldownSkipInfo and is called twice from CooldownSkip
(cooldown skip list first, trusted_packages on top so trusted entries
override the reason on overlap).
- Audit log every exemption, not just SkipAll: a new auditCooldownSkip
helper in proxy/interceptors/cooldown.go emits one event per match
(package-wide or per-version), each tagged with its source list.
LogCooldownSkipped gains a version argument for the per-version case.
- Cover the trusted_packages reason path in TestCooldownSkip.
* fix(cooldown): avoid double-auditing trusted package exemptions
auditCooldownSkip now only emits EventTypeCooldownSkipped for entries
that came from dependency_cooldown.skip. Trusted-package exemptions
already get an EventTypeInstallTrustedAllowed event at tarball-download
time (proxy/interceptors/base_registry.go), so emitting a cooldown event
for them too would double-count the same waiver.
* emit trusted and cooldown skip events to cloud
* fix tests
* refactor(cooldown): return value from collectCooldownSkip, short-circuit on trusted SkipAll
Address PR review feedback:
- Rename cooldownSkip to collectCooldownSkip and return CooldownSkipInfo
instead of mutating an input pointer.
- Add mergeCooldownSkip to combine per-list results with trusted_packages
taking precedence on overlap.
- CooldownSkip now consults trusted_packages first and returns immediately
on a package-wide trusted exemption (DC skip list cannot add anything).
- Extend tests to cover disjoint pinned entries across both lists and the
case where DC version-less subsumes a trusted pinned entry.
* fix(audit): address cooldown review feedback
* fix(cooldown): audit cooldown skips at download time with concrete version
Backend rejects PackageVersion messages without a version, and audit logs
should reflect the runtime fact (a specific version was skipped) rather
than the config rule. Move the audit emission from metadata-request
handling to download-request handling, where the concrete version is
known, and require version in LogCooldownSkipped.
* chore(audit): drop dead scope assignment in LogCooldownSkipped
* refactor(cooldown): move skip-list logic into cooldown handlers
Registry interceptors no longer compute CooldownSkip or branch on SkipAll;
they just call HandleMetadataRequest. The npm and pypi cooldown handlers
own the skip lookup, the package-wide exemption short-circuit, and (for
pypi) the canonical-name denormalization. Also align LogCooldownSkipped
with other LogXxx signatures by taking *packagev1.PackageVersion.
* fix: Simplify audit logging for dependency cooldown skip
* refactor: Simplify cooldown handling and maintain separation of concepts for trusted and DC skip packages
* fix: Code review fixes
* fix: Emit cooldown skipped audit event ONLY when an in-window version is skipped
---------
Co-authored-by: Abhisek Datta <abhisek.datta@gmail.com>
* fix(proxy): do not override explicitly-set CI env var
pmg forces CI=true for non-interactive (non-PTY) proxy runs so package
managers behave non-interactively. This clobbered a CI value the user set
explicitly (e.g. CI=false on a build server), changing downstream tool
behavior unexpectedly.
Only inject CI=true when CI is not already present in the environment,
preserving the user's intent. mergeEnv override semantics are left intact
since other overrides (HTTP_PROXY, etc.) must clobber.
Fixes#335
* test(proxy): snapshot/restore CI env explicitly in override test
Address review feedback: make the unset-CI subtest's intent explicit by
snapshotting the original CI value, unsetting it for the test, and
restoring it in t.Cleanup instead of relying on t.Setenv cleanup.
---------
Co-authored-by: Claude <noreply@anthropic.com>
* fix(pty): treat background jobs as non-interactive to avoid SIGTTOU stop
IsInteractiveTerminal only checked that stdin/stdout are TTYs. A background
job (pmg npm run test &) still has the TTY on stdin/stdout, so pmg picked
PTY mode and called tcsetattr to enter raw mode. Changing terminal modes
from a background process group makes the kernel stop the process with
SIGTTOU, leaving the job hanging in Stopped state.
Check that the process group is the terminal's foreground process group
(tcgetpgrp == getpgrp) before treating the terminal as interactive, so
background jobs fall through to direct execution.
Fixes#322https://claude.ai/code/session_01PBBo5CKkzg68MMGrgCTQcY
* test(pty): fail on output copy timeout to avoid racy buffer read
Reading the output buffer after a silent select timeout races with the
io.Copy goroutine still writing to it. Fail the test on timeout instead.
Also fix a grammar nit in the IsInteractiveTerminal doc comment.
https://claude.ai/code/session_01PBBo5CKkzg68MMGrgCTQcY
---------
Co-authored-by: Claude <noreply@anthropic.com>
* fix(shim): recognize shims at arbitrary paths via PMG_SHIM_PATH
The recursion guard in FilterPMGFromPath hardcoded the `/.pmg/bin`
suffix, so shims placed anywhere else (e.g. `/usr/local/lib/pmg/bin`,
`/shims`, or any future system-wide location) would not be stripped
from PATH when PMG resolved the real package manager. The shim would
resolve back to itself and PMG would re-exec it in an infinite loop.
This blocks moving shims out of `~/.pmg/bin` — needed for a future
`pmg setup install --system` (#317) — and also any user attempt to
relocate shims manually.
Have the shim export its own path before exec'ing pmg, and let the
filter use that to strip the exact dir at runtime. Keep the legacy
suffix check as a fallback so already-installed shims keep working
until they are regenerated.
Also drop `PMG_SHIM_PATH` from the env passed to the real package
manager so child processes don't inherit a stale marker.
* docs(shim): clarify PMG_SHIM_PATH is internal and unsupported to set manually
* remove comment
* update comment
* feat: authenticated Malysis analyzer with tenant exclusion support
When SafeDep Cloud credentials are available (keychain or environment),
PMG now uses an authenticated malware analysis query against
api.safedep.io instead of the unauthenticated community endpoint
(community-api.safedep.io). The API key and tenant ID are supplied via
the gRPC connection.
The authenticated response may carry a tenant-specific malicious package
exclusion. This is honored as an opt-in trust signal: a flagged package
is downgraded to allow only when a concrete exclusion (non-empty ID) is
present for the exact package version queried. Exclusions are never
honored for community queries and never weaken the verdict for packages
that were not flagged. Allowed-by-exclusion packages are surfaced as a
warning so the trust decision is never silent.
Changes are additive; non-authenticated usage is unchanged. Credential
resolution is extracted into internal/cloudauth and reused by both the
analyzer factory and the existing cloud sync client.
* fix: surface tenant exclusions in proxy mode; clarify comments
- Warn when proxy interceptor allows a flagged package due to a tenant
exclusion, matching the guard flow so the trust decision is not silent.
- Remove stray doc comment above warnIfExcluded.
- Clarify that a verified-malware verdict can be downgraded by an
exclusion in applyExclusion.
---------
Co-authored-by: Claude <noreply@anthropic.com>
* feat: add CloudSinkEnvResolver interface with default implementation
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* feat: add GitHub Actions environment resolver for cloud sink
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* feat: populate invocation context with CI environment on cloud events
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* fix: address lint errors in cloud sink tests
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* refactor: use getter-based CloudSinkCIResolver with nil-when-no-CI
Rename to CloudSinkCIResolver with focused CI concern. Factory returns
nil when no CI is detected, removing the need for IsCI() and a default
resolver. Leaves room for a separate agent resolver in the future.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* feat: add CI metadata support using updated API SDK
Update SDK to include SetMetadata on EndpointCIContext. Add Metadata()
to CloudSinkCIResolver interface and GitHub Actions implementation
(workflow, job, run_attempt, server_url). Wire metadata into
buildInvocationContext.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* refactor: address review comments on CI resolver
- Inject CloudSinkCIResolver as dependency into newCloudSink for testability
- Check both GITHUB_ACTIONS and GITHUB_RUN_ID for GHA environment detection
- Make factory and constructor package-private (newCloudSinkCIResolver,
newGithubActionsCIResolver)
- Attach invocation context only to session complete events, not every event
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* fix: fail fast on os.Getwd error instead of swallowing it
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 4.6 <noreply@anthropic.com>
* fix: avoid resolving symlinks in shim PMG binary path
Shims hardcoded the resolved Cellar path (e.g.
/opt/homebrew/Cellar/pmg/0.16.0/bin/pmg) instead of the stable
Homebrew symlink. This broke all shims after `brew upgrade` since
the old Cellar directory is removed.
Fixes#302
* fix pip test pkg version
* feat: add doctor check runner core types and logic
* feat: add doctor checks for config, binary, directory, and aliases
* feat: add doctor checks for sandbox and security features
* feat: add protection verification check using test malicious packages
* feat: add summarized package manager availability check
* feat: add pmg setup doctor command with compact output
* feat: add PATH shim verification to doctor command
* fix: improve doctor command UX and alias detection
- Capitalize all check messages for consistent output
- Dim passing checks, color warn/fail for visual clarity
- Silence empty Cobra error output on doctor failure
- Remove redundant pmg binary check (self-evident)
- Fix alias IsInstalled to skip commented-out source lines
- Improve protection failure message
* refactor: remove package manager availability check from doctor
* fix: handle os.RemoveAll error in doctor protection check
* refactor: use table layout for setup doctor, extract shared table renderer
Move renderTable, truncate, and visibleWidth helpers from cmd/sandbox
to internal/ui so both sandbox and setup doctor share them. Rewrite
setup doctor output to use the same table structure as sandbox doctor.
Fix VisibleWidth to count runes instead of bytes for correct alignment
with multi-byte UTF-8 characters.
* docs: add pmg setup doctor to README, remove manual verification step
* refactor: use constants for check names, rename and inline doctor helpers
Address PR review comments: extract check name constants, rename
CheckConfigFile to CheckFileExists and CheckDirectoryWritable to
CheckDirectoryExists for reusability, inline trivial wrappers
(CheckSandbox, CheckSecurityFeature, CheckProxyMode), and add
fix hints for all checks with correct config keys.
* refactor: inline simple doctor checks into command layer
* fix: skip protection check when aliases and shims are inactive
Protection checks now fail immediately when shell aliases and shims
are both inactive, instead of falsely passing by running through the
pmg binary directly. Also clean up summary messages to remove
redundant fix hints and truncated paths.
* feat: Add support for background sync
* refactor: Maintain single source of truth for command defn
* fix: Code review fixes
* fix: Code review fixes
* docs: Add corner case inline doc
runner.Execute was not filtering ~/.pmg/bin from the environment
passed to child processes. This caused two bugs:
1. Sandboxed commands (bubblewrap) inherited the unfiltered PATH,
so child processes resolved package manager binaries to the shim
instead of the real binary, causing "file not found" errors.
2. Direct pmg invocations (pmg npm install) would spawn subprocess
that find the shim in PATH, causing infinite recursion (shim →
pmg → shim → pmg) until the system runs out of OS threads.
The proxy flow already filtered the environment via setupEnvForProxy
and FilterPMGFromEnv. This applies the same filtering to the
non-proxy execute path.
* feat: add FilterPMGFromPath utility for PATH shim recursion prevention
* feat: add FilterPMGFromEnv to filter PATH from env slices
* feat: filter ~/.pmg/bin from PATH in proxy subprocess env
* feat: add PathExport method to Shell interface for shim PATH integration
* feat: add ShimManager for PATH shim install/remove lifecycle
* feat: wire ShimManager into setup commands with --use-aliases fallback
* refactor: add DefaultShimConfig helper to reduce setup boilerplate
* fix: resolve real binary path to prevent shim double-invocation
exec.CommandContext resolves the binary using the current process PATH,
which still contains ~/.pmg/bin. This caused pmg to launch the shim
instead of the real package manager, resulting in a second pmg instance
with its own proxy — producing duplicate error messages and wasted work.
ResolveRealBinary searches a filtered PATH (without ~/.pmg/bin) to find
the real package manager binary before execution.
* fix: resolve real binary in runner.Execute and expand path resolution tests
Ensure guard mode and proxy skip paths also resolve through
ResolveRealBinary to prevent infinite shim recursion. Add table-driven
tests covering error cases, multi-binary PATH, and PATH restoration.
* fix: handle error return values from os.Setenv and file Close calls
Address errcheck lint failures: check os.Setenv returns in
ResolveRealBinary, and check f.Close/tempFile.Close in ShimManager.
* feat: auto-migrate shell aliases to PATH shims on setup install
When running `pmg setup install`, detect existing shell aliases and
automatically remove them before installing shims. Existing users
get a seamless migration with no extra flags or commands needed.
* fix: update E2E test to verify shim installation instead of alias RC file
Replace the .pmg.rc file check with assertions that ~/.pmg/bin/ exists
and contains executable shim scripts for npm and pip.
* feat: add FilterPMGFromPath utility for PATH shim recursion prevention
* feat: add FilterPMGFromEnv to filter PATH from env slices
* feat: filter ~/.pmg/bin from PATH in proxy subprocess env
* feat: add PathExport method to Shell interface for shim PATH integration
* feat: add ShimManager for PATH shim install/remove lifecycle
* feat: wire ShimManager into setup commands with --use-aliases fallback
* refactor: add DefaultShimConfig helper to reduce setup boilerplate
* fix: resolve real binary path to prevent shim double-invocation
exec.CommandContext resolves the binary using the current process PATH,
which still contains ~/.pmg/bin. This caused pmg to launch the shim
instead of the real package manager, resulting in a second pmg instance
with its own proxy — producing duplicate error messages and wasted work.
ResolveRealBinary searches a filtered PATH (without ~/.pmg/bin) to find
the real package manager binary before execution.
* fix: resolve real binary in runner.Execute and expand path resolution tests
Ensure guard mode and proxy skip paths also resolve through
ResolveRealBinary to prevent infinite shim recursion. Add table-driven
tests covering error cases, multi-binary PATH, and PATH restoration.
* fix: handle error return values from os.Setenv and file Close calls
Address errcheck lint failures: check os.Setenv returns in
ResolveRealBinary, and check f.Close/tempFile.Close in ShimManager.
* feat: auto-migrate shell aliases to PATH shims on setup install
When running `pmg setup install`, detect existing shell aliases and
automatically remove them before installing shims. Existing users
get a seamless migration with no extra flags or commands needed.
* fix: update E2E test to verify shim installation instead of alias RC file
Replace the .pmg.rc file check with assertions that ~/.pmg/bin/ exists
and contains executable shim scripts for npm and pip.
* feat: install both aliases and shims for full coverage
Aliases win in interactive shells (including venvs), shims catch
non-interactive contexts (IDEs, CI, subprocesses). Remove --use-aliases
flag and migration logic since both are always installed together.
Update E2E to verify all shim scripts and alias RC file.
* feat: address review feedback for shim implementation
- Install both aliases and shims together for full coverage
- Move homeDir resolution into NewDefaultShimManager (internal concern)
- Add mutex to ResolveRealBinary to guard against concurrent PATH mutation
- Use filepath.SplitList for platform-correct PATH splitting
- Add ResolveRealBinary to runner.Execute and proxy flow to prevent
shim recursion in all execution paths
- Remove print side-effects from ShimManager.Remove
- Update E2E to verify all shim scripts and alias RC file
- Expand ResolveRealBinary tests with table-driven cases
* fix: restore errcheck handling and add concurrency test for ResolveRealBinary
- Restore proper defer with log.Warnf for PATH restoration in ResolveRealBinary
- Restore errcheck handling for f.Close() and tempFile.Close() in ShimManager
- Add explanatory comment for ResolveRealBinary call in proxy_flow
- Add TestResolveRealBinaryConcurrent to verify mutex guards concurrent access
* feat: skip shell integration on Windows with informative warning
On Windows, pmg setup install now writes only the config file and
prints a warning that shell aliases and PATH shims require WSL.
* fix: PMG use pre-resolved binary path (#253)
---------
Co-authored-by: Abhisek Datta <abhisek.datta@gmail.com>
* feat: emit cloud events for dependency cooldown and host observations (#237)
Wire cooldown blocks and proxy host observations through the cloud sync
pipeline so they appear as telemetry in Control Tower.
- Cooldown blocks emit PACKAGE_DECISION with COOLDOWN_BLOCKED action and
PmgDependencyCooldown context (publish date, cooldown days, days since
publish, days remaining)
- Proxy host observations emit HOST_OBSERVATION with PmgHostObservation
(hostname, method)
- Session summary now includes cooldown_blocked_count
- Updated buf API dependency for new proto schema
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* format file
* fix: add explicit eventlog mapping for EventTypeDependencyCooldown
Follow the existing pattern where every audit event type has an explicit
case in mapEventType and a corresponding constant in the eventlog package.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* Apply suggestion from @devin-ai-integration[bot]
Co-authored-by: devin-ai-integration[bot] <158243242+devin-ai-integration[bot]@users.noreply.github.com>
Signed-off-by: Abhisek Datta <abhisek.datta@gmail.com>
---------
Signed-off-by: Abhisek Datta <abhisek.datta@gmail.com>
Co-authored-by: Claude Opus 4.6 <noreply@anthropic.com>
Co-authored-by: Abhisek Datta <abhisek.datta@gmail.com>
Co-authored-by: devin-ai-integration[bot] <158243242+devin-ai-integration[bot]@users.noreply.github.com>
- Replace nested policies map with flat skip_commands map in ProxyConfig
- Make skip_commands dependent on install_only being enabled
- Move proxy configuration docs from proxy.md to proxy-mode.md
- Update config template and tests for new schema
* feat: add ProxyConfig struct with per-PM skip_commands and legacy fallback
* feat: consolidate proxy config into structured section with backward compat
Replaces flat proxy_mode/proxy_install_only keys with a structured proxy
section supporting per-package-manager skip_commands. Legacy keys are
respected via fallback when user's config lacks the new proxy section.
Removes deprecated experimental_proxy_mode config and flag.
* fix: env var resolution for nested config keys and deduplicate skip command matching
- Add "." to "_" in Viper env key replacer so nested keys like
sandbox.enabled resolve from PMG_SANDBOX_ENABLED (was silently broken)
- Export IsFirstNonFlagArgInList and remove duplicate from proxy_flow.go
- Add table-driven tests for skip command matching with real-world cases
- Remove redundant env var test
* docs: update proxy configuration and env var documentation
Update config.md env var table to reflect new proxy.enabled and
proxy.install_only keys. Add proxy configuration section to proxy.md
covering config structure, per-PM skip commands, CLI flags, and env vars.
* fix: legacy fallback precedence
ConfigureSandbox was only triggered by IsInstallationCommand(), missing
update commands (npm update, pnpm update, etc.) that pull new versions
and run postinstall scripts. Use MayDownloadPackages() as the sandbox
signal so all package-downloading commands are sandboxed.
Co-authored-by: Abhisek Datta <abhisek.datta@gmail.com>
* feat: Show cooldown report for pinned version installs
When a user installs a package with an explicit version (e.g.
npm install foo@1.2.3) and that version falls within the dependency
cooldown window, the cooldown block is now recorded and shown in the
report. Previously, the report only appeared when ALL versions of a
package were in cooldown (remaining == 0), causing pinned version
installs to fail with a confusing "version not found" error from the
package manager instead of a clear cooldown explanation.
Introduces InterceptorContext to carry per-execution data (pinned
versions) from the CLI command through the interceptor layer, keeping
it separate from long-lived dependencies like the analyzer and cache.
* fix: Normalize PyPI pinned version keys for cooldown lookup
CLI-provided package names (e.g. Flask_Cors) don't match the
URL-parsed form (flask-cors). Normalize keys once at construction
time so cooldown lookups match correctly.
* fix: Handle dots in PyPI package name normalization per PEP 503
denormalizePyPIPackageName already documented [-_.] replacement but
only handled underscores. Now also replaces dots with hyphens so
names like zope.interface match the URL-parsed form zope-interface.
* refactor: Extract shared cooldown stats recording into helper
Deduplicate identical stats-recording blocks from npm_cooldown.go
and pypi_cooldown.go into recordCooldownStats in cooldown.go.
* fix: Distinguish explicit version pins from auto-resolved versions
PyPI parsers resolve all packages to concrete versions (even without
a user-specified constraint), so HasVersion() was always true. Add
IsExplicitVersion to PackageInstallTarget, set it only when the user
provided an explicit constraint. Use it in proxy_flow.go to avoid
false pinned-version cooldown reports.
* feat: Add proxy_install_only config to restrict proxy to download commands
Introduces proxy_install_only (default: false) which, when enabled,
skips the proxy for package manager commands that do not download
packages (e.g. npm ls, pip list), avoiding unnecessary MITM overhead.
- Add ProxyInstallOnly to Config and config template
- Add IsKnownDownloadCommand / MayDownloadPackages to ParsedCommand
- Add DownloadCommands to npm and pypi PM configs covering update,
ci, audit, dlx, exec, x, download, run and equivalents per PM
- Extract shared runner.Execute used by both proxy flow and guard
- Proxy flow short-circuits to runner.Execute for non-download commands
when proxy_install_only=true
* refactor: Inject CommandExecutor into guard to fix dependency direction
guard depended on internal/runner, which inverted the intended layer
hierarchy. Now guard defines a CommandExecutor function type and accepts
it as a constructor argument. internal/flows (the composition root)
creates the executor closure wrapping runner.Execute and injects it,
keeping guard free of internal/ dependencies.
* refactor: Invert proxy_install_only logic to use known non-download commands
Replace the DownloadCommands allowlist (opt-in, fail-open) with a
NonDownloadCommands denylist (opt-out, fail-safe). The proxy now runs
for all commands except those explicitly known to not download packages.
Unknown or future package manager subcommands default to running with
the proxy.
Includes script runners (run, start, test, stop, restart) that can spin
up local servers — setting proxy env vars on these breaks them without
providing any security benefit. Also covers removal commands and local
operations that never contact the registry.
* fix: Support PMG_* env vars regardless of config file state
AutomaticEnv only resolves env vars for keys Viper already knows about
via AllKeys(). When a key is absent from the config file (commented out,
new key added after last setup, or no config file at all), Viper had no
knowledge of it and silently skipped the env var.
Fix by registering all Config struct fields as Viper defaults via
reflection (using mapstructure tags) before reading the config file.
This ensures PMG_* env vars work in all cases.
Precedence: cobra flags > env vars > config file > defaults.
SetDefault is used (not Set) so env vars and config file can still
override the Go defaults freely.
Tests added covering all precedence levels including the key-absent-
from-config-file case that was the original bug report.
* fix: Only check first non-flag arg against NonDownloadCommands
Scanning all args caused false proxy bypasses when package names or
script arguments matched a NonDownloadCommands entry. For example:
- npm exec test → "test" matched, proxy incorrectly skipped
- npm update config → "config" matched, proxy skipped
- npm publish --tag version → "version" matched, proxy skipped
Fix by checking only the first non-flag argument (the subcommand).
If it is not in NonDownloadCommands we break immediately, so trailing
args never influence the classification. Applied to all four parsers:
npm, pip/pip3, uv, and poetry.
Regression tests added for the false positive cases.
* refactor: Replace reflection-based Viper defaults with embedded template
Load the embedded config template as the Viper base so all keys are
registered upfront, enabling PMG_* env vars to work regardless of
whether a key exists in the user's config file.
* fix: Restore trusted_packages template entry and revert DefaultConfig change
* docs: Document environment variable overrides for config keys
* update npm test cmd
* refactor: extract shared non-download command detection helper
Replaces duplicated first-non-flag-arg detection loops in npm.go and
pypi.go (pip + poetry parsers) with a shared isFirstNonFlagArgInList
helper in packagemanager.go.
https://claude.ai/code/session_01AHaKF3vc2Haj9tK3jgUBAs
---------
Co-authored-by: Claude <noreply@anthropic.com>
Sahilb315